一、水泥抗壓夾具是根據我國建材行業標準JC/T683-1977制造。水泥抗壓夾具是 標準"水泥膠砂強度檢驗方法(ISO法)GB/T17671-1999"設備。
First, the cement compression fixture is manufactured in accordance with China's building material industry standard JC / T683-1977. The cement compressive fixture is the standard "cement mortar strength test method (ISO method) GB / T17671-1999" equipment.
二、水泥抗壓夾具技術參數：
★上、下壓板寬度：40mm±0.1mm
★上、下壓板表面的平面為：0.01mm
★上、下壓板及傳壓柱硬度：≥60HRC
★球座環帶高度在2/3處，寬4-5mm
★上、下壓板長度方向的重合度：≤0.2mm
★上、下壓板自由距離：大于45mm
★ 定位銷的高度不高于下壓板表面：5mm
★定位銷硬度：大于55HRC
★傳壓柱材料硬度：大于55HRC
★框架底部A定位孔直徑：Φ8mm
★毛重/凈重：5kg
Technical parameters of cement compression fixture:
★ Width of upper and lower platen: 40mm ± 0.1mm
★ The plane PR of the surface of the upper and lower platens is 0.01mm
★ Hardness of upper and lower pressure plates and pressure transmission columns: ≥60HRC
★ The tee ring is 2/3 in height and 4-5mm in width
★ Overlap degree of the upper and lower pressure plates: ≤0.2mm
★ Free distance of upper and lower pressure plate: more than 45mm
★ The height of the positioning pin is not higher than the surface of the lower platen: 5mm
★ Positioning pin hardness: greater than 55HRC
★ Hardness of pressure transmitting column material: more than 55HRC
★ A positioning hole diameter at the bottom of the frame: Φ8mm
★ Gross / Net Weight: 5kg
三、水泥抗壓夾具校驗方法：
★目測檢查外觀。水泥抗壓夾具應保護清潔，不得碰傷劃痕，應有牢固的銘牌。
★上、下壓板應為硬質鋼材制成，其長度為40±0.1mm，寬度為40mm，厚度>10mm。
★上、下壓板與試件整個接觸表面的平面公差為0.01mm，上、下壓板自由距離>45mm。
★上壓板上的球座A應在夾具A軸線與上壓板下表面的交點上，公差為±1mm，上壓板隨著與試件的接觸而自動找平。
Third, the cement compression fixture calibration method:
★ Visually check the appearance. Cement compression fixtures shall be protected from scratches and scratches, and shall have firm nameplates.
★ The upper and lower pressure plates should be made of hard steel, with a length of 40 ± 0.1mm, a width of 40mm, and a thickness of> 10mm.
★ The plane tolerance of the entire contact surface between the upper and lower pressure plates is 0.01mm, and the free distance of the upper and lower pressure plates is more than 45mm.
四、水泥抗壓夾具結構特點：
主要由下夾具座、上夾具座、標準夾輥、抗劈裂夾具上下壓條組成。下夾具座通過定位銷、墊圈固定在壓力機活塞上，上夾具座通過上支座、菱形銷及壓力機上的定位銷和兩內六角螺釘固定在壓力機橫梁上。
Fourth, the structural characteristics of the cement compression fixture:
It is mainly composed of a lower clamp base, an upper clamp base, a standard nip roller, and an upper and a lower bead for anti-cracking jig. The lower clamp seat is fixed on the press piston by positioning pins and washers, and the upper clamp seat is fixed on the press beam by the upper support, diamond pins, and positioning pins on the press and two hexagon screws.
五、水泥抗壓夾具使用注意事項：
★使用前對限位尺寸檢查是否還保持正確位置；
★如果擋銷磨損超差，可以進行打磨修復；如果擋板、插銷、定位錐頭銷磨損超差，可以重新組裝，錯開磨損部位后繼續使用
V. Precautions for using cement compression fixture:
★ Check the limit size before use to maintain the correct position;
★ If the stop pin wears out badly, it can be polished and repaired; if the baffle, latch, and positioning cone pin are out of wear, it can be reassembled, and it can continue to be used after staggering the worn parts.
