瀝青混合料單軸壓縮試驗機是檢測儀器，用于測定熱拌瀝青混合料的抗壓回彈模量的抗壓強度。用微電腦控制。保證數據準確，有效避免了人為因素影響，測試數據準確，性能穩定可靠。
Asphalt mixture uniaxial compression tester is a testing instrument for determining the compressive strength of the compressive rebound modulus of hot-mixed asphalt mixtures. Controlled by microcomputer. Ensure the data is accurate, effectively avoid the influence of human factors, the test data is accurate, and the performance is stable and reliable.
瀝青混合料單軸壓縮試驗機按照《公路瀝青路面設計規范》（JTJ 014）確定瀝青混合料結構層的設計參數時英按本方法執行。如無特殊規定，用于計算彎沉的抗壓回彈模量的標準試驗溫度為20℃，用于驗算彎拉應力的抗壓回彈模量的標準試驗溫度為15℃。加載速率為2mm/min。（圓柱體法）
Asphalt mixture uniaxial compression testing machine is determined in accordance with the "Asphalt Pavement Design Code for Highways" (JTJ 014) when the design parameters of the asphalt mixture structural layer are determined by this method. If there is no special requirement, the standard test temperature for calculating the compression rebound modulus of bending is 20 ° C, and the standard test temperature for calculating the compression rebound modulus of bending stress is 15 ° C. The loading rate is 2mm / min. (Cylinder method)
瀝青混合料單軸壓縮試驗機技術指標：
★上升速率：（50±5）mm/min
★壓頭直徑：（102±0.2）mm
★大壓力：50KN 精度 1％
★流值范圍：0－15.00mm 精度 ±0.1mm
★環境溫度：≤30℃。
★相對濕度：≤85%。
★整機功耗：≤700W。
★外型尺寸：650x480x900mm
★儀器凈重：100kg
★電源電壓：220v
Technical Specifications of Asphalt Mixture Uniaxial Compression Tester:
★ Rising rate: (50 ± 5) mm / min
★ Indenter diameter: (102 ± 0.2) mm
★ High pressure: 50KN, accuracy, 1%
★ Flow value range: 0－15.00mm, accuracy ± 0.1mm
★ Ambient temperature: ≤30 ℃. Zh
★ Relative humidity: ≤85%.
★ Power consumption: ≤700W.
★ External dimensions: 650x480x900mm
★ Net weight of the instrument: 100kg
★ Power supply voltage: 220v
瀝青混合料單軸壓縮試驗機主要特點：
★設有過載保護，下降過位保護。
★操作簡便，測試數據準確，性能穩定可靠。
★儀器自動試驗，顯示并打印試驗壓力及對應的流值，繪制試件受力變形的坐標曲線圖。
★可存儲15組試件的試驗結果。
★大型液晶屏顯示。
★流值檢測有單路與雙路兩種。
★試驗由儀器或計算機自動控制，試件受壓變形過程數據及曲線由計算機自動存盤并顯示，可通過打印機打印輸出，好彩色噴墨打印機。
★機器配有USB接口。
★可選配串口，上位機軟件可以進行分析處理。
Main Features of Asphalt Mixture Uniaxial Compression Tester:
★ With overload protection and falling over-position protection.
★ Easy operation, accurate test data and stable and reliable performance.
★ The instrument automatically tests, displays and prints the test pressure and the corresponding flow value, and draws the coordinate curve diagram of the test piece's deformation.
★ Can store the test results of 15 groups of test pieces.
★ Large LCD screen display.
★ There are two types of current value detection: single and dual.
★ The test is automatically controlled by the instrument or computer. The data and curve of the compression deformation process of the test piece are automatically saved and displayed by the computer, and can be printed out by a printer. Good color inkjet printer.
★ The machine is equipped with a USB interface.
★ Optional serial port, PC software can analyze and process.
瀝青混合料單軸壓縮試驗機本方法適用于直徑100mm±2.0mm,高100mm±2.0mm的瀝青混合料圓柱體試件。
儀具與材料
材料試驗機，其它可施加荷載并測試變形的路面材料試驗設備也可使用，但均必須滿足下列條件：
大荷載應滿足不超過其量程的80%，且不小于量程的20%的要求，宜采用100kN，分度值100N。具有球形支座，壓頭可以活動與試件緊密接觸。
具有環境保溫箱，控溫準確度0.5℃。當缺乏環境保溫箱時，試驗室應設置空調，控溫準確度1.0℃。
能符合加載速率保持2mm/min的要求。試驗機宜有伺服系統，在加載過程中速度基本不變。當采用馬歇爾試驗儀手動控制時，應事先校正手搖速率，以達到2mm/min加載速率的要求。
變形量測裝置
抗壓試驗加載用上下壓板，下壓板下有帶球面的底座。壓板直徑120mm，在直徑102mm處有一淺的放置試件的圓周刻印。下壓板直徑線兩側有立柱頂桿，上壓板直徑線兩側裝有千分表架，表架中間與頂桿中間位置一致。當使用機具有自動測定試件垂直變形或自動測記試件的壓力與變形曲線功能時，可以直接使用，不必另外配備變形量測裝置。
千分表（1/1000mm）,2只。
恒溫水槽：用于試件保溫，溫度能滿足試驗溫度要求，控溫精密度±0.5℃。恒溫水槽的液體應能不斷循環回流。深度應大于試件高度50mm。
臺秤或天平：感量不大于0.5g。
溫度計：分度為0.5℃。
Asphalt mixture uniaxial compression tester This method is suitable for asphalt mixture cylinder test pieces with a diameter of 100mm ± 2.0mm and a height of 100mm ± 2.0mm.
Instruments and materials
Material testing machines, other pavement material testing equipment that can apply loads and test deformation can also be used, but all must meet the following conditions:
The large load should meet the requirements of not exceeding 80% of its measuring range and not less than 20% of its measuring range. 100kN and 100N division value should be used. With a spherical support, the indenter can move in close contact with the test piece.
With environmental insulation box, the temperature control accuracy is 0.5 ℃. When there is no environmental insulation box, the test room should be equipped with air conditioner, and the temperature control accuracy is 1.0 ℃.
It can meet the requirement of maintaining the loading rate of 2mm / min. The testing machine should have a servo system, and the speed is basically unchanged during the loading process. When the Marshall tester is used for manual control, the hand-cranking rate should be calibrated in advance to meet the requirement of 2mm / min loading rate.
Deformation measuring device
The upper and lower pressure plates are used for the compression test loading. The lower pressure plate has a base with a spherical surface. The pressure plate has a diameter of 120mm, and there is a shallow circumferential mark on the diameter of 102mm. There are column jacks on both sides of the lower pressure plate diameter line, and dial gauges are installed on both sides of the upper pressure plate diameter line. When the machine has the function of automatically measuring the vertical deformation of the test piece or automatically measuring the pressure and deformation curve of the test piece, it can be used directly without the need to additionally provide a deformation measurement device.
Dial indicator (1 / 1000mm), 2 pcs.
Constant temperature water tank: It is used for the insulation of the test piece, the temperature can meet the test temperature requirements, and the temperature control precision is ± 0.5 ℃. The liquid in the thermostatic water tank should be able to circulate continuously. The depth should be greater than the height of the test piece by 50mm.
Bench scale or balance: the sense is not more than 0.5g.
Thermometer: The division is 0.5 ℃.
